G-13T5CQ07ZV
top of page

Where Extreme High-Aspect Ratio (EHAR) Holes are Utilized

Writer: Kirk Abolafia
Kirk Abolafia
11 minutes ago
11 min read

When discussing microhole features that serve the semiconductor or aerospace industries, it’s the hole's aspect ratio that is a key metric of how challenging it is to machine: that aspect ratio simply being its depth divided by its diameter. For manufacturers producing small features by drilling, anything beyond 10:1 is considered a deep hole, according to UNISIG. This article, though, is about holes that go much, much further: extreme high-aspect-ratio, or EHAR, holes run 30:1, 50:1, 60:1 and in some applications can be as high as 300:1. To put that in perspective, a 300:1 hole about as wide as a fine sewing needle (0.5mm) would run 150mm deep, roughly the length of a ballpoint pen.

While they sound small or insignificant, entire industries depend on these EHAR features. In this article, we'll first walk through three applications where EHAR holes do critical work. Then we'll cover why these holes are so hard to make with conventional processes, and finally where pulsed electrochemical machining (PECM) fits.

Key Takeaways

  1. Deep holes start at 10:1. EHAR holes run from about 30:1 to 300:1, and every added millimeter of depth makes them harder to produce.

  2. Fuel injector bodies, semiconductor gas distribution plates and turbine blade cooling holes all depend on EHAR holes.

  3. Small, deep holes multiply the challenges of conventional drilling, especially in tough materials, at greater depths and with internal geometry such as intersections.

  4. Challenges increase further when EHAR features need superfinished surfaces, varied diameters along their length or curved paths.

  5. PECM machines EHAR holes without contact or heat, and Voxel has produced holes up to 300:1 in Inconel, including several at once.




Where EHAR Holes Do Critical Work

EHAR holes tend to show up, fundamentally, wherever a fluid has to travel a long way through solid metal in a very small passage (whether that’s for cooling, or delivery purposes). Let’s review three key areas where these EHAR features can be found.

1. Fuel Injection: Injector Bodies and High-Pressure Bores

A modern diesel injector carries fuel at extreme pressure through a long, narrow bore in the injector body. One tooling maker cites injection pressures of up to 2,500bar in common rail systems. To put that in perspective, it's more than twice the water pressure at the bottom of the Mariana Trench (about 1,071bar, per Wikipedia), and roughly 1,000 times the pressure in a car tire. Pressures this high matter because they atomize fuel into a finer spray that burns more completely. When Denso introduced its 2,500bar common rail system, it reported up to 3% better fuel efficiency and up to 50% lower particulate emissions compared with its previous generation (DieselNet). One documented production case from EUROTEC describes a 1.5mm bore drilled through the full 90mm length of an injector holder in tempered 42CrMo steel. In other words, that is a 60:1 aspect ratio hole in a refractory metal alloy, being produced at 400,000 parts per year: an extremely difficult, task in and of itself requiring incredibly high part volumes.



Diesel fuel injectors face incredibly high pressure standards, requiring excellent straightness and surface quality. Credit: creative commons license.
Diesel fuel injectors face incredibly high pressure standards, requiring excellent straightness and surface quality. Credit: creative commons license.


Consider the wear that occurs every injection cycle: with that amount of pressure, each cycle loads its walls, meaning ultra-straightness and superb surface condition are key factors deciding its part life.  The bore also meets cross-holes that feed and return fuel, and those intersections concentrate stress: any burr or loose particle left there travels downstream toward a nozzle and needle that already runs on very tight clearances. In other words, the quality of one long hole affects how precisely an engine meters fuel for its entire service life.

2. Semiconductor Gas Hardware: Distribution Plates and Showerheads

Pivoting to the semiconductor world: in deposition and etch chambers (the tools that build a chip layer by layer: deposition chambers lay down films only nanometers thick, and etch chambers use reactive gases to carve circuit patterns into them), process gas reaches the wafer through a gas distribution plate, often called a showerhead. The plate's job is to spread gas evenly across the entire wafer surface, and its holes decide how evenly that happens. One patent for a gas distribution plate with high aspect ratio holes describes the holes at about 100–600µm in diameter with aspect ratios of at least about 50:1, at counts of about 50,000 holes or more, and preferably 100,000 or more, in plates about 200–350mm across. Common materials for these critical parts include a variety of aluminum, molybdenum and nickel alloys: the latter of which can be notoriously challenging to machine in precise geometries and features.


Fab equipment like this sometimes requires high-aspect-ratio features that are incredibly precise. Photo sourced via creative commons license.
Fab equipment like this sometimes requires high-aspect-ratio features that are incredibly precise. Photo sourced via creative commons license.


The biggest question is in relation to the biggest challenge of these semicon parts: why so many long, narrow holes? A longer hole builds more flow resistance per hole, which helps balance gas delivery across the plate so the center and edge of the wafer see the same gas, on an ultra-microscopic level. If one hole turned out to be ever-so-slightly larger, tapered or partly blocked, that region of the wafer gets a different dose, and film thickness or etch depth changes with that- permanently ruining that wafer and incurring potentially significant costs. On top of all that: burrs and loose particles add even more risks of contamination since a single particle shed from a gas hole can land directly on a wafer (we covered this in a previous article: Particle Risk & Semiconductor Hardware).

3. Turbine Blade Cooling Holes

Turbine blade cooling holes are probably among the most well-known EHAR application, and are also the most extreme. Modern gas turbines run hot gas past blades at incredibly high temperatures the blade alloy couldn't survive on its own (even nickel superalloys), so cooling air is fed through internal passages and out through rows of small holes. One GE patent on electrochemical machining tools notes that these cooling holes “commonly have an aspect ratio, or depth to diameter ratio, as large as 300:1.”

Predictably, the quality of those holes (particularly, its straightness and internal surface quality) ties directly to engine performance. Each hole meters cooling air, and every bit of air diverted to cooling is air that doesn't do work in the turbine. Meanwhile, a hole that's oversized just wastes air, while one that's undersized or partly blocked leaves part of the blade running hot. We explored the economics of this in another recent article: Micro-Feature Quality, Macro-Economic Impacts: Aerospace & Fuel Efficiency.

And taking it a step further: the most advanced cooling designs ask for more than a straight, uniform hole. The same GE patent from earlier also describes adding ridges and local enlargements (called turbulators) inside cooling holes to, “effect turbulent flow through the hole and increase cooling efficiency.” Curved cooling holes can cover the critical hot areas of a component that a straight hole can't reach, such as blade platforms. Furthermore, holes that change diameter along their length or follow a gentle curve put cooling exactly where the blade needs it.

Section digest

  1. Injector bores run around 60:1, and their surface and intersection quality affect fatigue life and fuel metering.

  2. Gas plates can need 100,000 or more holes at 50:1, where hole-to-hole uniformity sets process uniformity on the wafer.

  3. Turbine cooling holes reach 300:1, and the best designs add varied diameters and curved paths.


Why EHAR Holes Are So Incredibly Difficult

Across all three applications, the core problems for manufacturers are fundamentally the same: the deeper and narrower a hole gets, the harder it is to clear debris and keep the tool on its intended path. Each additional challenge (be it material, or surface quality, or hole features) is an add-on of this fundamental challenge.

Every conventional process runs out of depth

Let’s first look at how well microdrilling tackles EHAR. In a single sentence: a drill has to constantly remove chips through the hole it's cutting…and a long, slender drill may begin to walk, chatter, and deflect. That gets harder quickly as drills shrink. A drill's bending stiffness falls with roughly the fourth power of its diameter, so a drill half as wide bends about 16 times more easily at the same length, and an EHAR hole demands a drill that is both long and thin. Inconel makes it slower still. In one 2023 study, 6mm drills were fed through Inconel 718 at just 6–12mm per minute, and a high-speed steel drill showed wear after only two holes (Manufacturing Technology).


Arrays of cooling channels on turbine blades are among the most common, and most difficult, EHAR features to machine. Photo credit: creative commons.
Arrays of cooling channels on turbine blades are among the most common, and most difficult, EHAR features to machine. Photo credit: creative commons.

In another, 10.5mm carbide drills cutting 30mm-deep holes in Inconel took about a minute per hole with peck drilling and lasted only 9–29 holes without vibration assistance (Liao et al., 2007). Those holes are only about 2:1 and 3:1. At EHAR depths and sub-millimeter diameters, drilling Inconel means near-constant pecking and a real risk of a drill snapping off inside a nearly finished part.

EDM, despite being non-contact, still has to flush eroded debris out of an ever-deeper gap, and a 2023 study describes flushing as the key factor for being able to machine precise high-aspect-ratio boreholes, notably worse as electrode diameters shrink. Speed is the other limit. Fast-hole EDM, which uses a rotating tube electrode, typically drills holes about 0.3–3.2mm in diameter, according to a 2003 Cutting Tool Engineering article. The same article describes a 457mm-long, 3.2mm hole in titanium that took 1.5 hours to drill, and a 305mm electrode that lasted only 12–15 holes through 25mm of stainless steel. EDM can reach very high aspect ratios in small diameters, but every hole it makes carries a recast layer that has to be removed or accepted.

Laser drilling, while incredibly efficient for large arrays of holes, tends to lose energy and accuracy with depth. Most sources consider laser drilling’s limits to be somewhere around the 10:1 aspect-ratio range, making it largely inapplicable to the EHAR discussion.

Process

What limits depth

What it leaves behind

Where it works well

Twist drilling / gundrilling

Chip evacuation, drill walk, minimum practical diameter

Burrs at exits and intersections; residual stress

Larger diameters, very long straight bores

EDM drilling

Debris flushing, electrode wear with depth

Recast layer, heat-affected zone

Small holes in hard alloys at moderate depth

Laser drilling

Energy delivery and taper with depth

Recast, heat-affected zone, taper

Fast, shallow holes in thin sections

Electrochemical drilling (STEM, PECM)

Electrolyte flow and gap control

No recast or heat-affected zone; burr-free

Small, deep holes in conductive alloys, up to 300:1

Qualitative comparison. Actual limits depend on diameter, material and equipment.

Tough materials and production volume make it worse

Many EHAR applications tend to require incredibly difficult-to-machine alloys, as an additional headache. This can be for their high corrosion resistance, temperature flux resistance, or high load cycle capabilities. Inconel and other turbine alloys hold their strength at temperature and work-harden quickly, wearing through cutting tools (see our deep dive on Inconel). At 300:1, mechanical drilling isn't an option at all. EDM and laser drilling handle shorter cooling holes, but both leave a recast layer, and recast in a cooling hole becomes a crack-start site under the thermal cycling every blade sees (see Microcracks: Their Scale & Importance).

Part volumes add their own form of pressure on manufacturers: holding straightness over 90mm already takes careful tooling, staged drilling and stable coolant delivery, and every tool change risks a step or misalignment in the bore. At hundreds of thousands of parts per year, even small rates of tool breakage or drift will add up quickly. In the semicon world: one company notes that spindle drills have a practical minimum diameter of about 500µm, so its workaround is to stack thin plates about 200–900µm thick, drilled separately and then brazed or diffusion-bonded with the holes aligned. That methodology works, sure, but every added layer can be another alignment issue compounded upon itself, and 100,000 holes across several plates is a lot of features to keep identical (see our article, The Role of Uniformity in Critical Manufacturing).

Internal Geometries, Superfinishes, and Varied/Curved Diameters

Let’s not forget the issues go even further when discussing the internal features or geometries in these EHAR parts. An intersection 50 diameters deep inside a part is out of reach for brushes and hand tools (and visual inspection too). Long drilled passages drift off center, so two passages meant to meet cleanly can meet with an offset that leaves a sharp lip. Thermal deburring and abrasive flow machining treat many internal burrs, but importantly, each has trade-offs: thermal methods affect every exposed edge at once, and abrasive media can lodge in passages or round edges unevenly. Verifying that every intersection in a production lot is clean is often the hardest part of the job. In hydraulic manifolds and fuel controls, a missed burr is a reliability risk: Extrude Hone, a company that sells deburring equipment, describes the chain in a 2026 article on manifold deburring, where particles circulate in the oil, filters clog early and valves stick or fail.

The hardest EHAR features, as we mentioned, go beyond a straight, uniform hole. A surface finish specification deep inside a 100:1 hole can't be met by polishing afterward (since no polishing tool reaches it) so the finish has to come from the process that made the hole itself. A hole that changes diameter along its length, such as a turbulated cooling hole, needs a process that can selectively remove more material at specific depths.

Add on an even bigger challenge with curved holes are harder still. Drilling, EDM and laser drilling all cut along a straight line from the entry point, so none of them can follow a curved path.

Have a long bore, gas plate or cooling hole that's pushing your current process? Contact us at info@voxelinnovations.com.

Where PECM Fits

PECM removes metal by controlled anodic dissolution, with no contact between the tool and the part and no heat input. It builds on the same electrochemical foundation that has long been used for the deepest turbine cooling holes, and adds pulsed power for tighter control of the gap between tool and part. For EHAR holes, that brings several advantages.

  • Extreme depth in tough alloys. Voxel has produced EHAR holes in Inconel up to 300:1, including several at once. Removal doesn't depend on hardness, so work-hardening alloys machine on the same terms as softer ones.

  • No recast or heat-affected zone. Holes carry no recast layer or thermally altered material, which removes a common crack-start site in cooling holes and fatigue-loaded bores.

  • Varied diameters. Voxel produces holes whose diameter changes along their length, for features such as turbulated cooling holes or flow-tuned passages. Note: The nitinol test coupon below shows several of these profiles in EHAR holes.

  • Slightly curved holes. Voxel's methodology produces gently curved holes for turbine cooling features, geometry that straight-line processes can't reach.

  • Superfinished bores. PECM produces fine surface finishes as part of the process, down to 0.005–0.4µm Ra on tough materials, including inside features no polishing tool can reach.

  • Many identical holes. One cathode machines many holes in a single pass with minimal tool wear, so hole 1 and hole 10,000 come from the same process conditions, which matters for gas plates and cooling-hole rows.

  • Clean intersections. PECM leaves burr-free edges and can put a controlled radius on deep internal intersections in injector bodies and manifolds, with no media to clean out afterward (see PECM & Sharp or Rounded Edges).



A nitinol test coupon, sectioned to expose five EHAR holes machined with PECM. Each hole uses a different profile along its length.




Close-up of the same cross section. The holes change diameter along their length, from evenly spaced bulbs similar to turbulated cooling holes, to flared and enlarged ends, to a gently rippled wall.

For semiconductor gas plates, PECM's depth capability may allow fewer, thicker layers, or a single piece, compared with a stack of thin laser-drilled plates. For fuel-system components where a drilled bore is already in place, PECM may be most relevant as the step that finishes deep intersections. In both cases, whether the trade works depends on the material, hole count and specification.

PECM has limits too, though. It works on conductive metals only, cathode access sets the limit for internal features, and hole-to-hole consistency still depends on electrolyte flow, fixturing and cathode design.

Closing Thoughts: Why Depth is Key

Across fuel injection, semiconductor gas hardware and turbines, EHAR holes share one trait: the deeper the hole, the more every flaw is magnified. A few micrometers of taper or a burr at an intersection matters more as the hole gets longer and narrower, because it affects flow and fatigue along the hole's full length.

A strong apparent PECM fit still needs a look at the specific part: diameter, depth, material, hole count, tolerance stack, inspection needs and expected volume. A borderline application isn't an automatic no either. Those are the variables our team works through on every EHAR inquiry.

Capability Snapshot: PECM for EHAR Holes

Capability

What Voxel has produced

Highest aspect ratio

Up to 300:1 in Inconel

Parallel EHAR holes

Multiple 300:1 holes machined at once

Hole geometry

Varied diameters along the hole length (shown in nitinol); slightly curved holes

Microholes

300µm microholes in copper

Parallel features

Tens to hundreds of features per custom cathode, per pass

Tool life

Thousands of identical parts from one cathode (minimal tool wear)

Thermal effects

No heat-affected zone, no recast layer

Edge condition

Burr-free, with a specifiable edge radius

Surface finish

Down to 0.005–0.4µm Ra on tough materials

Materials

Conductive metals, including Inconel, nitinol, stainless steel, titanium, copper, tungsten and molybdenum

Results depend on the specific geometry and material.

Send Us the Hole Your Current Process Can't Reach

Working on a long bore, gas distribution plate, cooling hole or manifold passage that's pushing past 30:1? Send Mike and Kirk the hole diameter, depth, material, tolerance and expected volume, and we'll tell you whether PECM is worth a closer look. You can also request a 15-minute fit discussion at info@voxelinnovations.com.

 
 
 

Comments


bottom of page